Inorganic Chemistry
Metallurgy: Isolation of Metals
From ore to pure metal, covering ores and concentration (froth flotation, magnetic separation, leaching), calcination and roasting, the thermodynamics of reduction and the Ellingham diagram, extraction of iron, copper, zinc and aluminium, and refining by distillation, liquation, electrolysis, zone refining and vapour phase methods
NEET style
Removed from the rationalised NCERT books and from the NEET UG syllabus since 2024, so expect at most a stray fact inside another chapter’s question
JEE style
Not in the JEE Main syllabus since 2024, while JEE Advanced still tests Ellingham diagram reading, roles of reagents (cryolite, NaCN depressant, silica flux, Zn in the cyanide process), refining methods and Faraday law numericals
Ores and concentration
Naturally occurring compounds of metals are minerals; a mineral from which a metal can be extracted profitably is an ore. The unwanted earthy material is gangue.
| Metal | Important ores |
|---|---|
| Aluminium | Bauxite (0 < x < 1); kaolinite |
| Iron | Haematite , magnetite , siderite , iron pyrites |
| Copper | Copper pyrites , malachite , cuprite , copper glance |
| Zinc | Zinc blende (sphalerite) ZnS, calamine , zincite ZnO |
- Hydraulic washing (gravity separation): heavier ore particles settle in a stream of water.
- Magnetic separation: magnetic ores (magnetite, wolframite) are separated from nonmagnetic gangue.
- Froth flotation for sulfide ores: the ore is wetted by oil and carried up in the froth; the gangue is wetted by water and sinks. Collectors (pine oils, fatty acids, xanthates) make the mineral particles less wettable by water; stabilisers (cresols, aniline) stabilise the froth; a depressant such as NaCN keeps ZnS down while PbS floats.
- Leaching dissolves the ore in a suitable reagent, as in the Bayer process for bauxite and the cyanide process for silver and gold.
- 1Bayer process: digest the powdered ore with concentrated NaOH at 473 to 523 K and 35 to 36 bar: (silica dissolves as silicate; iron oxide and are left behind).
- 2Neutralise with : (seeded with fresh hydrated alumina).
- 3Heat at 1470 K: .
Cyanide leaching (M = Ag, Au); the metal is then displaced by zinc: 2[M(CN)₂]⁻ + Zn → [Zn(CN)₄]²⁻ + 2M
Calcination, roasting and the thermodynamics of reduction
Calcination
- Heating in limited air or no air
- For carbonates and hydrated oxides
- Volatile matter (CO₂, H₂O) escapes
Roasting
- Heating in a regular supply of air below the melting point
- For sulfide ores
- SO₂ is used to make sulfuric acid
Reduction of an oxide by a reductant is feasible when the coupled reaction has , that is, when the oxidation of the reductant has a more negative than the oxidation of the metal.
- The Ellingham diagram plots against T for the formation of oxides per mole of .
- Most lines slope upward: gaseous is consumed, so . The line for slopes downward (: one mole of gas becomes two), and is almost flat.
- A metal (or C, CO) can reduce the oxide of any element whose line lies above it at that temperature. Where two lines cross, the reduction becomes feasible on one side of that temperature.
- Above about 1073 K the C→CO line falls below the Fe→FeO line, so coke reduces FeO in the hotter part of the blast furnace (NCERT). The CO→CO₂ and C→CO lines cross near 983 K (a figure from outside NCERT): below this CO is the better reductant (NCERT’s answer at 673 K is CO), above it carbon is.
- Limitation: the diagram shows only thermodynamic feasibility, not the rate of reduction.
Extraction of iron, copper, zinc and aluminium
| Blast furnace zone | Reactions |
|---|---|
| 500 to 800 K (upper, cooler part) | ; ; |
| 900 to 1500 K (lower, hotter part) | ; |
| Slag formation | ; |
- 1Copper: roast the sulfide ore, then smelt with silica; iron oxide forms slag (), leaving matte ( + FeS).
- 2In the silica lined converter, a hot air blast first removes the remaining iron as slag, then , then self reduction . Escaping gives blister copper its look.
- 3Low grade copper ores are leached with acid or bacteria and is reduced with scrap iron or .
- 4Zinc: ZnO is made into briquettes with coke and clay and reduced by coke at a higher temperature than copper needs; NCERT writes (other sources put zinc smelting nearer 1300 to 1400 K). The zinc distils off and is collected by rapid chilling.
- Aluminium (Hall Héroult process): purified is mixed with cryolite or , which lowers the melting point of the mix (alumina alone melts above 2300 K) and makes it conduct. A steel cell lined with carbon is the cathode; graphite rods are the anodes.
- Cathode: . Anode: and . Overall: , so the anodes burn away, about 0.5 kg of carbon per kg of aluminium (NCERT).
Refining
| Method | Principle | Metals |
|---|---|---|
| Distillation | Low boiling metal is vaporised and condensed | Zn, Hg |
| Liquation | Low melting metal flows off a sloping hearth | Sn |
| Electrolytic | Impure anode, pure cathode, salt solution; less reactive impurities form anode mud (Sb, Se, Te, Ag, Au, Pt) | Cu (CuSO₄ + H₂SO₄), Zn |
| Zone refining | Impurities are more soluble in the melt than in the solid; a moving heater sweeps them to one end | Si, Ge, B, Ga, In (semiconductors) |
| Mond process | ; | Ni |
| van Arkel method | ; decomposes on a hot W filament (about 1800 K) | Zr, Ti |
| Chromatography | Differential adsorption | Elements in minute amounts |
Formula bank
Coupled reduction
Faraday’s law
Hall Héroult overall
Cyanide leaching
Self reduction of copper
Mond process
Gibbs energy and equilibrium
Tricks & mnemonics
Calcine carbonates, roast sulfides
Ellingham rule
Refining matchmaker
Who does what in Al extraction
NaCN does two jobs
NCERT high yield lines
Original NCERT aligned summaries of the lines examiners love. Tap “Quiz me” to test yourself instantly.
- In froth flotation, collectors such as pine oils, fatty acids and xanthates make the mineral particles less wettable by water, and froth stabilisers such as cresols and aniline stabilise the froth.Class 12 · Isolation of Elements (earlier edition)
- The Ellingham diagram plots ΔfG° of oxide formation against temperature; the C→CO line slopes downward because the reaction increases the number of gas molecules.Class 12 · Isolation of Elements (earlier edition)
- In the electrolytic reduction of alumina, cryolite and fluorspar are added to lower the melting point of the mixture and increase its conductivity.Class 12 · Isolation of Elements (earlier edition)
- In the extraction of copper, Cu₂S and Cu₂O react together in the converter to give copper metal (self reduction); the solidified copper has a blistered appearance due to escaping SO₂.Class 12 · Isolation of Elements (earlier edition)
- Zone refining is based on the principle that impurities are more soluble in the melt than in the solid state of the metal.Class 12 · Isolation of Elements (earlier edition)
Exceptions to remember
Iron pyrites () is not used as an ore of iron.
NCERT: the abundant oxide ores are preferred because they do not produce polluting gases such as the SO₂ released from pyrites.
The line has a negative slope in the Ellingham diagram.
Gas moles increase, so ΔS is positive.
Below about 983 K CO is a better reductant than C; above it carbon is better.
Crossing point of the CO→CO₂ and C→CO lines.
Aluminium is not extracted by carbon reduction.
Al₂O₃ is extremely stable and carbon would form Al₄C₃ at the required temperature.
Copper needs no separate reducing agent in the converter.
Self reduction: Cu₂S reduces Cu₂O.
Silver and gold are extracted by first oxidising them (with /CN⁻) and then reducing with Zn.
Hydrometallurgy: soluble cyano complexes form only after oxidation.
In zone refining the impurities travel with the molten zone.
They are more soluble in the melt than in the solid.
The graphite anodes are consumed in the Hall Héroult cell.
Oxide ions discharge as O₂, which burns the carbon to CO and CO₂.
Solved problems
Practice
Column I: (P) cryolite in aluminium extraction (Q) NaCN in froth flotation of PbS and ZnS (R) silica in copper smelting (S) zinc in the cyanide process
Column II: (1) reducing agent (2) depressant (3) flux that removes iron oxide as slag (4) lowers the melting point and raises conductivity
Column I: (P) distillation (Q) liquation (R) van Arkel (S) Mond
Column II: (1) Ni (2) Sn (3) Zr (4) Zn
Ready for the real thing?
Take a timed, NTA style test on this chapter with instant analytics